HOW TO INSTALL A BATHTUB

How to Install a Bathtub

How to Install a Bathtub

Blog Article

Click Here To Read More

Are you currently interested in content around Tools You Need to Install a New Bathtub ?


Tools You Need to Install a New Bathtub
Installing a bath tub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently easily accessible, the task can relocate immediately; if you have to open up a wall to get rid of the old tub and place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. Make certain you have certified on your own for the job as well as fit trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This short article will certainly assist you install a new bathtub in your restroom if you have actually currently purchased a new tub and also do not need to alter the plan of your previous water system pipelines.
Your tools as well as product checklist must consist of the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Setup


    Firstly, the supporting structure provided with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
    Fit the flexible faucet adapters to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last placement.

    Removing Old Touches


    If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
    Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Setting up the Bath tub


    Utilizing the two wooden boards under its feet, position the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
    The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
    To install taps, fit all-time low of the outermost adaptable tap port to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
    Switch on the water supply and check all joints and new pipework for leaks and tighten them if required. Fill up the tub and likewise check the overflow outlet and the typical electrical outlet for leakages.
    Ultimately, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait till the bath tub has actually been made use of at least when as this will certainly resolve it right into its last setting.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a link to the current supply pipelines.
    If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the tap as well as the sink. Protect the faucet in position with the maker offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bath tub


    In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to split an inflexible seal, causing the water to penetrate the wall between the bath and the tiling, bring about issues with moisture as well as possible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the activity experienced when the tub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also quickly available on the marketplace. It is suggested to fit the tiles making use of water-resistant or waterproof sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    Do you really like reading about How to Install a Bathtub Yourself? Give feedback directly below. We would be delighted to listen to your ideas about this article. We are looking forward to see you back again in the near future. Please take the time to promote this post if you liked it. I praise you for your time. Kindly come visit our blog back soon.




    Set Up An Appointment


    Report this page